Water Heater Repair Lakewood

Make Sure Your Water Heater in Lakewood, Colorado is in Top Condition

Would you fancy a sudden temperature fluctuation while you are in the middle of a hot shower? Experiencing a sudden temperature rise in your shower can simply ruin your entire de-stressing endeavor. Such temperature shocks are witnessed when your water heater is not maintained adequately. And for this, you need professional help like the one offered at Todd’s. 

At Todd’s Water Heater Repair, our plumbers always look forward to a water heater replacement in Lakewood. Our services are also spread across Parker, Thornton, Westminster, Centennial, Aurora, Arvada, Highlands Ranch, Littleton, Englewood, Broomfield, Boulder, Golden, and Highlands Ranch. 

How to Maintain a Water Heater?

For household equipment, prevention is usually better (and less expensive) than cure, and that saying certainly applies to water heaters. If you want to keep your equipment in top shape for as long as possible, perform some of these routine maintenance tasks regularly.

Remember that water heaters have a lot of sensitive parts, and electric types might pose additional dangers. If you are unsure about your abilities to cope with these issues, get your water heater serviced by a professional and experienced plumber from Todd’s Water Heater Repair. 

As per our plumber, a hot water heater installation, hot water heater repair Lakewood, and hot water heater replacement Lakewood depend on the type of water heater you are dealing with. Different systems require a different approach: 

Steps to Maintain a Traditional Storage Tank Water Heater

  • Check to see if the cold water valve is closed, and the electricity is turned off.
  • Connect the drain valve to a hose.
  • Place the draining valve near a gutter, in a safe location where the outflow of hot water will harm no one.
  • Open both the pressure and drain valves at the same time.
  • Allow the tank to completely drain to ensure that all debris and silt are removed.
  • Turn on all the hot water faucets in the house, as well as the tank’s cold water valve.
  • Insert the hose’s draining end into a pail.
  • Fill the tank with cold water until the water flowing out of the hose is clean.
  • Close both valves and turn on the power supply once you are finished. 

Steps to Maintain a Tankless Water Heater

Mineral build-ups on the heating coils and the interior of the heating chamber are the major things to watch out for before opting for a tankless water heater installation Lakewood. These deposits can dramatically reduce the performance and lifespan of your heating systems if they are not removed. With proper maintenance, tankless water heaters can survive for up to 20 years. This is remarkable because any time you can save money in inflationary times and with high gas prices that are hurting so many people that’s something to pat yourself on the back for. 

  • Turn off your water heater’s main power supply.
  • Remove the water heater’s lid by unscrewing it.
  • Turn off all of your water heater’s main water valves. This will prevent water from entering or exiting your system while it is being cleaned.
  • The purge port caps on the cold and hot water valves should be removed. This will relieve any built-up pressure in the pipes and keep any hot water residue from splashing onto your skin. Make sure the rubber sealing discs stay in place when starting a removal.
  • Connect the hosing lines to each valve. Typically, these are bundled with the water heater.
  • By twisting the purge port valves perpendicular to the main cold and hot water valves, you can open them.
  • Clean the internal chamber of your water heater with a 2.5-gallon container of white vinegar.
  • Follow the instructions in your user handbook for flushing and draining.
  • The purge port valves should be closed.
  • Remove the rubber hose and disconnect it.
  • Change the purge port valve tops and tighten them down.
  • Find the filter. Remove the screw and clean the sediment chamber by running it underwater until it is empty. Replace the filter in its original location.
  • Instructions for properly restarting your water heater can be found in the manufacturer’s manual.
  • Run your hot water faucets for 2–3 minutes, or until no more air escapes the pipes.

How to Maintain a Hybrid How Water Heater?

Hybrid heaters, like traditional storage heaters, need to be drained and cleaned regularly. In addition, like tankless water heaters, their air filters must be cleaned regularly. For exact information on how to locate, remove, and replace air filters on your equipment, consult your manufacturer’s manual.

Temperature Regulations for Gas and Electric Water Heaters

Thermostats are included in both gas water heaters and electric water heaters, allowing you to change the temperature of the water, but the technique differs. To avoid the growth of hazardous germs, experts recommend a water temperature of 120° – 140° Fahrenheit. Temperatures greater than this can cause severe burns. 

Steps for Temperature Modulation in Gas Water Heaters 

  • Locate the red dial in the water heater compartment.
  • If temperatures are listed, set the temperature to between 120–140 degrees Fahrenheit. If no temperature is given, you can guess that warmth will be approximately 90–110 degrees and hot will be around 140–150 degrees.
  • You should be better off verifying the temperature of the water yourself because thermostats are notoriously unreliable.
  • Choose the faucet that is farthest away from the heater.
  • Turn it on and let the water run for a few minutes.
  • In a cup, collect the liquid that has resulted.
  • Using a thermometer, check the temperature of the water.

Steps for Temperature Modulation in Electric Water Heaters

  • The water heater’s power should be turned off.
  • Locate the heater’s access panel. If it is a larger heater, you may need to remove two separate panels.
  • Remove the thermostat’s insulation if it has any.
  • If there is a plastic cover on the device, remove it with caution using a screwdriver.
  • Above the heating element, see a thermostat screw, which you should carefully adjust with your screwdriver until it reads 120–140 degrees.  
  • Turn on the power supply and replace the lid and insulation.
  • Check the temperature of the water as described above.

Insights About Some Safety Features Embedded in A Hot Water Heater

According to our plumbers, here is a list of safety features installed in your water heater that you should know about:

Temperature Release Valve

In a 40-gallon tank, heated water can expand by more than half a gallon. If your tank is already full, the extra volume will be trapped inside, causing greater pressure throughout the inner system. This excess pressure is relieved by the temperature release valve. Each valve is equipped with a thermostat that is submerged in the tank’s top 6 inches of water. 

The valve is ordinarily closed, but when the thermostat reading exceeds a specified level, it is forced open, releasing surplus water and fumes. The majority of valves are made to discharge at 150 degrees Fahrenheit and/or 210 pounds per square inch (psi). 

As you can expect, the water expelled from the tank in these situations can be hot, so a copper, iron, or steel pipe is employed to channel effluent away from the tank to avoid this. This pipe should finish within 6 inches of the floor. The pipe must be expanded to the outside of the home in regions where the floor may be damaged.

Seismic Strap

Water heaters should be braced according to building requirements to avoid damage during seismic activity, which is prevalent in earthquake-prone areas. The straps should be fastened to wood blocking strips against the near wall to anchor the water tank. To support these columns and place them against the water heater, use heavy-duty steel brackets. 

Bollards 

If you keep your water heater in your basement, take precautions to safeguard it from damage caused by your car. Bollards are typically 36″ high and 4″ in diameter, and can be found at any local hardware shop. Your bollard should be made of a durable material and bright enough to be seen from any angle. Make sure it is bolted down to the floor, and if you are having difficulties with the installation, engage a plumber or contractor to help you out.

Safety Pans

In indoor locations, a solid heat-resistant drain pan should be placed beneath the water heater. This will protect your floor from the consequences of water heater leaks or pressure valve runoffs, as well as anyone else nearby. 

Why Choose Our Services?

Nothing is more important to Todd’s Water Heater Repair than our clients’ safety during the time of need. We are always ready to provide a pleasant plumbing experience swiftly and at a reasonable price, be it a Lakewood water heater replacement or a Lakewood water heater repair.

Todd’s plumbers are on a mission to deliver the greatest service and experience to each one of our clients to better serve the community. We make every effort to be available when you require assistance. We offer same-day plumbing service, knowledgeable and qualified technical support, 24-hour customer service, and cost-effective emergency plumbing solutions. 

We recognize the value of your water heater and provide same-day water heater installation, water heater repair Lakewood, and water heater replacement Lakewood. All you need to do is call us!

Location:

Lakewood, CO

Hours of Operation:

Sunday 8AM-8PM
Monday 8AM-8PM
Tuesday 8AM-8PM
Wednesday 8AM-8PM
Thursday 8AM-8PM
Friday 8AM-8PM
Saturday 8AM-8PM